piezoCi — Contact Instrument
A phantom-powered preamplifier for the direct, ground-free connection of piezo contact pickups – for example on a handpan.
The prototype
Testers of the piezoCi
Leander Greitemann and Alex Metzler (GLEICHMUTPROBEN) used the piezoCi live on stage – here their performance on 10 October 2026 in Mainz.
Jonas Straumann – Hearing-impaired. Musician. Creative mind. www.jonashandpan.com
The housing of the finished piezoCi
piezoCi – devices it works with
piezoCi (Contact Instrument) is a pickup preamplifier for the handpan. Like a condenser microphone, it is powered by the phantom power of the connected device; no power supply of its own or battery is needed. This is what we have tried so far:
-
Behringer FLOW 8 works Digital mixer with Bluetooth On a microphone input with 48 V phantom power switched on; enable the low cut at about 100 Hz.
- Connection
- XLR cable from piezoCi to a microphone input of the mixer. Switch on phantom power (+48 V) on the mixer for this channel.
- Setting
- Set the channel's low cut (high-pass filter) to about 100 Hz. This removes footfall noise, handling noise and low rumble before they load the rest of the chain.
- Sound
- With the low cut at 100 Hz the lowest notes sound slightly leaner. If you want more bass, set the low cut lower.
- Guide value
- Together with the high-pass filter in piezoCi, the −3 dB point of the chain is at about 55 Hz (calculated, without low cut on the mixer).
-
ESI Neva Duo and Teufel Mynd works USB audio interface with microphone preamps, followed by a Bluetooth speaker Signal path piezoCi → Neva Duo → Mynd. The sound is clean; at high volume, reduce the bass on the Mynd by about 3 dB.
- Connection
- XLR cable from piezoCi to a microphone input of the Neva Duo; switch on phantom power (+48 V) on the Neva Duo. From the output of the Neva Duo it continues to the Mynd.
- Why the Neva Duo?
- The Mynd has no XLR input and no phantom power. piezoCi needs both, which is why the Neva Duo sits in front of it.
- Setting
- The Mynd reproduces low notes strongly. At high volume it helps to reduce the bass on the Mynd by about 3 dB.
- Note
- piezoCi itself already suppresses frequencies below about 50 Hz. This takes low rumble off the Mynd that would otherwise overdrive it.
-
Fishman Loudbox Artist works Amplifier for acoustic instruments To the XLR input. The amplifier supplies 24 V phantom power, which is enough for piezoCi.
- Connection
- XLR cable from piezoCi to the XLR input of the Loudbox Artist.
- Phantom power
- The Loudbox Artist supplies 24 V instead of the usual 48 V. piezoCi works with it, but the headroom is smaller than at 48 V.
- Guide value
- By calculation, piezoCi needs at least about 21 V at the XLR input. If the phantom voltage under load is clearly below that, the circuit can drop out.
- Setting
- With the amplifier's Low control, low notes can be reduced further if needed. The high-pass filter in piezoCi is at about 80 Hz here (−3 dB, calculated).
-
Applies to all devices Requirements What a device has to provide Balanced XLR input with phantom power (24 V or 48 V).
- Input
- Balanced microphone input with XLR socket. piezoCi does not work on instrument or jack inputs without phantom power.
- Phantom power
- 24 V (P24) or 48 V (P48); piezoCi draws about 1.3 mA. Phantom power must be switched on at the device.
- Gain
- piezoCi amplifies by a factor of about 5.6 (around 15 dB) and has a balanced output. The rest is handled by the device's gain control.
- High-pass filter
- piezoCi contains two high-pass filters (input and output), together 12 dB per octave. Depending on the device, the −3 dB point is between about 55 and 80 Hz (calculated).
Other devices are possible but have not been tested by us. We are happy to answer questions.
As of October 2026. The information is based on Micon Audio Electronics' own tests; figures marked “calculated” are guide values derived from the circuit and may vary depending on the device and component tolerances.